快速调试电子地磅的方法

电子地磅使用的越来越多，但考虑到经济方面，现在只有很少的厂家会把砝码拉到现场去调试了，那是不是我们的地磅就不用调试了呢？不是这样的，电子地磅安装后，检查电子地磅的各个部位连接是否完好，电子地磅不应与基础任何部位接触，电子地磅与四周护边铁间距为10mm—15mm。

More and more electronic loadometer use, but considering the economy, now only a few manufacturers will pull weights to the scene to debug, that is not what we don't have the loadometer debugging? This is not the case, electronic loadometer after installation, check all parts of electronic loadometer connection is intact, electronic loadometer should not contact any part of the foundation, and around the edge of electronic loadometer iron spacing is 10mm - 15mm.

调试前，须先打开电源开关预热15分钟，并尽量用载重量接近最大秤量的车辆，往返多次通过和在承重台上刹车停留，用力矩扳手拧紧各称重传感器高强度螺栓。都是在工厂里面调好后出去的，那对于这种情况，我们该如何调试呢？下面我们就来讲一讲：

Before commissioning, we must first turn on the power switch and heat it for 15 minutes, and try to use the vehicle close to the largest scale with the carrying capacity close to the maximum weight. It will stop for many times to go on the way and stop on the bearing platform, and tighten the high-strength bolts of all weighing sensors with the torque wrench. All of them are adjusted in the factory and then go out. So how do we debug this situation? Now let's say:

1、电子地磅承重点调试好后，将相当于最大秤量的砝码均匀地加到电子地磅承重台上，按照各种称重显示器的说明书所介绍的位置和方法，使显示值与砝码值一致后，取下砝码，并确认空秤显示为“0”即可。最后，将最大秤量分为若干份，其中须包括该秤的最小秤量、最大秤量及允差改变的各个称量点，要求电子地磅各点的称量误差不大于各量点的最大允差要求。

1, electronic loadometer supporting point after commissioning, will be equivalent to the maximum weighing weight evenly applied to the electronic loadometer bearing platform, location and methods introduced in accordance with the various specifications of weighing display, the display value consistent with weight value, remove the weights, and confirm the empty scale shown as "0". Finally, the largest scale is divided into several parts, each weighing quantity and allowable maximum and minimum weighing scale which shall include the scale difference change, the requirements of electronic loadometer weighing error not greater than the maximum permissible amount of each point requirements.

2、用数字电压表依次测量电子地磅各个称重传感器的输出电压，如存在不一致，可分别调整接线盒中相应两只精密可调电阻，以减少相互间差异量。但调整量必须注意，两只可调电阻的旋转方向要一样，旋转量也要一样，顺时针转动时其电阻减小，输出电压变大，显示值增加，否则反之。直至调整到电子地磅各只称重传感器输出一致。 调试一般可用重量法进行，即将1/10最大秤量的砝码，依次放至电子地磅承重台中心位置及各只称重传感器上方的承重台上，并用实差法准确测出各只称重传感器输出的差异量，同时分别调整电子地磅各个承重点称重传感器相应的两只精密可调电阻，减少相互间的差异量，但旋转方向和旋转量也一样。

2, the digital voltmeter measurement of electronic loadometer weighing all the output voltage of the sensor, such as inconsistent, it can adjust the corresponding two boxes of precision adjustable resistance, to reduce the amount of the difference between. But the adjustment must be noted that the rotation direction of two adjustable resistors should be the same, and the rotation must be the same. When clockwise rotation, the resistance will decrease, the output voltage will increase, and the display value will increase. Otherwise, it will increase otherwise. To adjust to the electronic loadometer weighing sensor output. Debugging method is generally available weight, 1/10 maximum weighing weight, in order to put electronic loadometer bearing center and each bearing platform above the weighing sensor, and accurately measure the weighing sensor output difference with real difference method, at the same time adjust electronic loadometer weighing sensor corresponding each bearing point two precision adjustable resistance, reduce the difference between the amount, but also the same direction of rotation and rotation.

3、参考衡安称重软件电子地磅称重显示器使用说明书(专业技术手册)，检查各种功能键的正确性，提高电子地磅的称量准确度。

3, the reference value for an electronic loadometer weighing display weighing software instructions (technical manuals), check the correctness of the various function keys, improve electronic loadometer weighing accuracy.